Author: Johan Bouwer

Radio Amateur of the Year

Posted by

0

RAC Bulletin 2013-017E – Radio Amateur of the Year for 2012
2013-05-04

The RAC Board of Directors takes great pleasure in announcing the selection of Scott Wood, VE1QD of Halifax, Nova Scotia, as the Canadian Radio Amateur of the Year for 2012.

Scott celebrated sixty years in Amateur Radio in 2012. Over these years he has contributed enormously, and in many and varied ways both to our hobby and to radio in general. In his youth as a net controller in the Oregon State Fire Service, later as a radio operator in the US Naval Reserve, as a member of the Board of Directors for Radio for Peace International, in contesting and DXing, and in Elmering aspiring new hams, both young and old. However, it is the leadership in Amateur Radio that Scott has demonstrated locally, regionally, and internationally that is being recognized with this award. Scott has demonstrated vision, enthusiasm, dogged determination, and commitment to excellence in the area of Amateur Radio DXing through the establishment and management of the Maritime DX Forum for eight consecutive years. Scott envisioned the forum to be a venue where DXers in the region could come together annually to hear world-class, as well as local DX experts speak about important and current DX topics, and to provide a forum in which to share ideas with some of the best operators and leaders within the Amateur Radio community.

A presentation will be made to Scott by the RAC President at the RAC booth at the Dayton Ham Fest this month. A more detailed article will appear in an upcoming TCA/RAC Report

Geoff Bawden, VE4BAW
President and Chair RAC

Scholarship

Posted by

0

Scholarship Trust Announces Call for Applications
2013-05-05

The Brit Fader Scholarship was established in 1993 by the Halifax Amateur Radio Club and endowed through the generosity of Club members and Radio Amateurs throughout the Maritime Provinces of Canada. This scholarship is intended exclusively for post-secondary educational use, to provide assistance with the cost of tuition, room, board, books and/or other fees essential to the advanced education of the recipient. The amount of the 2013 award will be $1000.00.

Applicant must be a Canadian Citizen, but without regard to gender, race, national origin, handicap status or any other factor and must be performing at a high academic level.

Applicant must, hold an active Basic Class or higher grade of Canadian Amateur Radio license.

This Scholarship will be provided for attendance at an accredited Canadian post-secondary technical school, college or university, with preference given to applicants who have been accepted into a program in the field of electronics or electrical engineering, or related area.

Application submissions must be postmarked no later than July 12 th , 2013.

A zipped application package (Criteria; Application Form; Reference Form) is available for down-loading from the HARC website at www.Halifax-arc.org. Follow the link to the Brit Fader Scholarship from the Home Page under Education .

D. Howard Dickson, VE1DHD

for the Brit Fader Scholarship Committee

D. Howard Dickson
Radio Amateur – VE1DHD // VE1ZD
Seabright, Nova Scotia
CANADA

RAC Bulletin 2013-016E

Posted by

0

RAC Bulletin 2013-016E – RAC completes Review of Amateur Radio Exam Questions
2013-04-27

On April 17th 2013, RAC submitted the final documents called for in the contract it won to review the question banks used for exams for the Basic and Advanced certification of Canadian radio amateurs.

Industry Canada had issued a request for proposals to undertake the review in December 2012. RAC engaged RAQI to collaborate on the French language component of the work and submitted a response to the proposal. The $20,000 contract was awarded to RAC late in January.

The first phase of the contract, completed on March 13, consisted of a complete review of all the questions and answers used for amateur radio certification in Canada. At the end of this phase RAC delivered a comprehensive set of recommendations to improve and modernize the question banks. In most cases this involved detailed editing of existing questions but proposals were also made to delete or replace obsolete or inaccurate questions and add questions on aspects of amateur radio that had grown in importance since the last review.

The review concentrated on the accuracy and clarity of the questions and answers and recommended changes where required to eliminate possible confusion over the correct answer to each question. Some errors were easy to identify such as typing mistakes showing an obviously incorrect answer as correct. Others, particularly related to ensuring that all incorrect answers were truly incorrect, required more careful study. The review team took special care in comparing questions in both languages so that the English and French versions conveyed the same information.

Clear, accurate and understandable exam questions are an important element in making amateur radio accessible to all Canadians. RAC sees an up to date and well functioning exam system as an important element in bringing more people into amateur radio to ensure its continuation and growth, a priority objective of the national organization.

On April 4th, Industry Canada officials kicked off phase 2 of the project by providing a preliminary reaction to the RAC recommendations made in phase 1. Over the next 13 days the RAC-RAQI team reviewed the Industry Canada comments and where appropriate provided additional comments and recommendations.

The first phase had identified most areas of needed change and as a result the Phase Two report contained a significantly smaller set of recommendations. Industry Canada will make the final decision on changes to the questions after considering the RAC Phase 2 report. However the exchange of comments so far suggests that the RAC review will lead to a significant improvement and updating of the question banks.

RAC understands the importance of amateur radio courses and educational material developed and delivered by dedicated volunteers across the country. Changes in the question banks can lead to increased work by these volunteers and the Review Team worked to propose changes in ways that will minimize the updating. Many questions will remain as they were before the review. When proposing deleting obsolete questions the Team recommended replacement questions so that question numbering of the unchanged questions would not have to be changed.

RAC is already planning for the transition. Once Industry Canada makes public the updated questions banks, we will prepare information identifying where changes have been made to assist instructors in modifying their course materials and examiners in preparing for the change. As has been mentioned in previous bulletins, the curriculum has not been changed. The topics addressed in the exams and consequently in courses and educational material remain the same. The changed questions will assess the knowledge of these same topics but should be clearer, more accurate, more understandable and relevant to modern amateur radio.

RAQI has been an excellent partner in this project and all francophones should immediately see the vast improvement in the French language questions when the new questions banks are approved and made public.

A great deal of effort has gone into the review and we are happy that it is being received well. RAC will continue to work with Industry Canada through existing consultative arrangements to provide Canadian radio amateurs with the best possible circumstances to pursue their hobby. As well, based on the success of this project, RAC looks forward to competing for contracts on significant projects related to amateur radio if the opportunity presents itself in the future.

For more information contact Glenn MacDonell, Project Manager, Question Bank Update Project and Deputy Director Ontario North East, (ve3xra@rac.ca).

Geoff Bawden, VE4BAW
President and Chair RAC

**—-**

Vernon Ikeda – VE2MBS/VE2QQ
Pointe-Claire, Québec
RAC Blog Editor/RAC E-News/Web News Bulletin Editor

March News Letter

Posted by

0

It seems not possible to add the news letter and the pictures to WordPress. We will have to investigate it further.

 

VE3ERC-LUB

MARCH 2013 

Volume 3 Issue 3 

IN THIS ISSUE 

DX PROPAGATION PRIMER P.2

SDR DONGLE BASED RADIO P.4

WED. NITE NET P.5

RFM22 RADIO P.6

MARCH MINUTES P.7

 

President: Al, VE3TET

Vice-President: Johan, VA3JBO

Secretary: Bob, VE3IXX

Treasurer: Reg, VE3RVH

Trustee: open

QSL Manager and Lighthouse: Bill, VE3WBJ

Repeater manager and maintenance person: Carl, VE3FEF

Website Admin: Johan, VA3JBO

VE3QB, Bruce’s antenna system. The white shed just behind the evergreen tree is his dedicated “ham shack”.

Now that many more amateurs can now use the HF bands, I thought it might be useful to explain the most basic elements of DX propagation.

The sun emits electromag-netic radiation and matter as part of the nuclear fusion process. Electromagnetic radiation in the ultraviolet region ionizes the F region, radiation in the soft x-ray area ionizes the E region, and radiation of the hard x-rays ionizes the D region.

The F region (made up of F1 and F2) is the prime region for ham radio DX operation.

SUNSPOTS (not to be confused with Solar

Flares) are areas on the sun emitting ultraviolet radiation. Thus they are tied to the ioniza-tion of the F region. The spot in the centre of the picture would swallow the earth. The Smoothed Sunspot Number (SSN) is calculated using six months of data before and after the desired month, plus the data for the desired month. Because of this amount of smoothing, the official SSN is one-half year behind the cur-rent month. Unfortunately this amount of smoothing often masks any short-term unusu-al solar activity that may enhance propagation, and so the eSSN (effective SSN) is more useful on a daily basis.

A DX PROPAGATION PRIMER

Or HOW YOUR SIGNAL GETS FROM

YOU TO ANOTHER HAM

Part 1 Compiled by

Bill Graham VE3ETK

SOLAR FLARES are guided into the ionosphere along magnetic field lines and thus can only impact high lati-tudes where the magnetic field lines go into the earth. Solar matter (which includes charged particles—electrons and protons) is ejected from the sun on a regular basis, and this comprises the solar wind. On a “quiet” solar day the speed of this solar wind heading toward earth aver-ages about 400 km per sec-ond and so there is a delay between the happening and the effect. The sun’s solar wind significantly impacts

Earth’s magnetic field. Instead of being a simple bar magnet, Earth’s magnetic field is compressed by the solar wind on the side facing the sun and is stretched out on the side away from the sun (the magnetotail, which ex-tends tens of earth radii downwind). The sun’s electromagnetic radiation can impact the entire ionosphere that is in daylight.

There are two measurements of this effect: the daily A index and the three hour K in-dex. The A index is an average of the eight three hour K indices, uses a linear scale and goes from 0 (quiet) to 400 (severe storm). The K index uses a quasi-logarithmic scale and goes from 0 to 9 (with 0 being quiet and 9 being severe storm). Generally an A index at or below 15 or a K index at or below 3 is best for propagation.

SDR Dongle-based Radio by Terry VE3XTM 

At our February meeting I gave a talk as well as a demonstration of “dongle” based Software Defined Radio (SDR). These dongles are devices that plug into your computer’s USB port. They were originally designed for DVB-T which is for receiving European digital television. The dongles do not work for North American TV as we use a different digital standard here.

However, SDR for these dongles began when DVB kernel developer Antti Palosaa revealed that an ecnomical USB EzTV 668 DVB -T/FM/DAB USB dongle based on the RealTech RTL2832U chip, could be used to stream raw I/Q samples to most PC’s. Since that time enterprising amateurs and software developers have written several programs to present this digital data in a very versatile open source software defined radios that are available for a free download on the Internet.

A recent article in QST titled, Cheap and Easy SDR, by Robert Nickels, W9RAN, outlined how to get SDR up and operating on your PC.

http://www.davegardner.org/Ham/PDF/EasySDR.pdf

Basic USB dongles such as the Terratec dongle are capable of receiving radio frequencies from about 54MHz up to about 2GHz. There are some that are capable of going lower in frequency down to 24MHz. The dongles will receive all modes, AM, FM, FM stereo, USB, LSB, DSB and CW. These dongles cost about $20 and with the proper antenna one can listen in on the VHF, UHF and microwave portions of the band, including stereo broadcast FM .

The article by Nickles outlines how to download and install the software using a simple batch file install procedure. The soft-ware version that most are using is the SDRSharp or SDR#.

SDR# screen shot showing the panadapter and waterfall screen Source http://sdrsharp.com/ 

The software allows the setup and frequency correction calibration of the radio, as well as adjustments to sampling rates, sen-sitivity and a range of other features, including the storage of favourite frequencies and a recording/playback of band activity, all in the VHF and UHF bands.

But all is not lost for those who prefer to work in the HF bands. Recent development have seen the design and availability of reasonably price up-converters that allow the use of the dongle in our favourite amateur bands. The up-converter boards are available for about $50. A few SMA adaptor cables are all that is needed to complete a basic SDR radio that will cover the range from the AM broadcast band up to the lower part of the microwave spectrum. For a review of the various up-converters available see the link below.

While we cannot expect these dongles to rival commercial radios at this time, they do give amateurs an introduction to SDR and the ability, with the panadapter, to see the signals on the various bands. We are only at the beginning of this new radio technology and the future will hold many more developments through the creative use of software and digital processing of signals.

WEDNESDAY NITE NET CONTROLLERS

APRIL 3 – DOUG VE3CXU

APRIL 10 – CARL VE3FEF

APRIL 17 – BILL VE3ETK

APRIL 24 – M E E T I N G

 

MAY 1 – AL VA3TET

MAY 8 – RALPH VE3EUC

MAY 15 – HARRY VE3EIX

MAY 22 – M E E T I N G

MAY 29 – WALLY VE3LCR

 

THE RFM22 RADIO PROJECT

BY JAMES LITWILLER VE3JLC 

The RFM22 is a low-cost ISM (Industrial, Scientific & Medical) FSK (Frequency Shift Keying) transceiver module which offers communication at tuneable frequencies in the 70cm band. It has an adjustable output power of up to +17 dBm. The wide operating voltage of 1.8-3.6 volts, plus a low current consumption makes the RFM22 an ideal little project.

This is the 3rd or 5th iteration of my RFM22 FSK radio project proto-type. These are won-derful little radios that can have you dreaming about the wildest software projects. Also the choice of the Arduino Pro mini 3 volt prototype board makes many things quickly possible and can easily enough run two radios at the same time.

I’m not sure yet how this is going to come together, as just a fox hunt radio that makes a little puff sound on the amateur radio 70cm band or other more advanced possibilities. To-day, I thought it might be interesting to try to construct a compact antenna to accompany the radio. Previously, a 1/4 wave length wire was used, which was fine, but opportunities exist for many possibilities.

Two 40mAh lithium batteries are intended to power this project. Connecting them in parallel could have complications, but I don’t think it will cause a power outage (Hi Hi) and some tests have shown that with precautions it can be done safely. Software projects will need to attempt power considerations. The container for an SD memory card (as shown in the photo) works as a god case for the project.

Further information can be found at:

Www.sparkfun.com/products/9821

http://arduino.cc/en/

http://playground.arduino.cc/

 

MINUTES FOR THE MARCH MEETING

 

WILF VE3HYV

ROB VA3AHP

JIM VE3JLC

REG VE3RVH

GREG VA3GSM

BRUCE VE3QB

JOHAN VA3JBO

PAUL VE3PVB

TERRY VE3XTM

JIM VE3JMU

CARL VE3FEF

RALPH VE3EUC

AL VA3TET

GORD VE3EOS

RICH VE3DCC

DOUG VE3CXU

HARRY VE3EIX

BOB VE3IXX

 

The meeting was begun with each member introducing their name and call sign. Gord VE3EOS, who was visiting, was warmly welcomed.

The first order of business was the Treasurer’s Report. Reg VE3RVH handed out his annual statement and reminded everyone that the membership fees are due. The ERC has $2,551.68 in the bank. Reg made a motion to accept the minutes and it was se-conded by Bruce VE3QB.

The second item on the agenda was that Al needed some-one to help assess the equipment from the estate of Bing Harris. Ralph (VE3EUC) volunteered to go with him. There will also be a need for volunteers to dismantle Bing’s tower and 4-element beam. Johan VA3JBO, Jim VE3JMU and Terry VE3XTM will set a date with Al to get the job done.

For new business, Bruce VE3QB explained some of the diffi-culties he encountered to re-configure the IRLP on his computer when he changed servers. It took several phone calls to Dave Cameron before he finally got it up and running well again. Our thanks to Bruce for his hard work. Bruce suggested that the club make a cash donation to the IRLP service and made a motion to send them $50.00. This was seconded by Ralph VE3EUC.

Reg VE3RVH giving the Treasurer’s Report.

Al spoke about the fleamarket on June 2 and about the need for more volunteers to run the Ontars net. He said that we will need about five people to cover the hours. Paul VE3PVB, Bob VE3IXX offered to help Al. Rich VE3DCC and Harry VE3EIX may possibly be able to help as well.

Al reminded all members to mark their calendar for the Field Day (June 22 and 23) at Bob’s (VE3IXX) farm. Al moved that the Sunday meal again be the traditional steak or roast beef dinner. This was seconded by Johan VA3JBO.

The final item of business was a discussion of the Lighthouse weekend (in Au-gust) at Point Clarke. Given the difficulties with a decent antenna last year and the fact that the lighthouse was still under re-construction, Al wondered whether it was even worthwhile to participate this coming August. He suggested that if the lighthouse is still not useable this summer, we may just forget this project.

Having finished the business part of the meeting, Al began a discussion of the up and coming ERC projects for this year. The first idea was for an HF pre-selector using a Cascode amplifier. Using schematic diagrams on the board, Al explained how this am-plifier works.

The second project idea was an EH antenna using a cone shape. While the flute shaped EH antenna (which Al and Paul had built a prototype) was more desirable, the cone shape is much simpler to build and works well. The EH antenna is only about three percent of a wavelength (great for smaller spaces), has a low noise level and works like an isotropic antenna.

EDITOR’S NOTE:

A special Note of thanks to Bruce VE3QB for his many frustrating hours of work trying to get his computer to run the IRLP for the ERC repeater.

We can all appreciate how difficult computers can be at times. Having the IRLP available to all who use our repeater is a great asset.